Flux - Full Pack 3.5.29 (NO INSTALL, SymLink Installer)

All credits goes to the respective people DESCRIPTION Spoiler: The DSP audio package, consisting of: Flux - Full Pack 3.5.29, IRCAM Tools 3.5.29, Level Magic 3.5.29, Pure Analyzer 1.10.4 Of Full Pack 2.2 Flux - a package of plugins for Mixing and mastering, comprising: Alchemist 3.5.29 Flux 3.5.29 E

资源介绍

VST AAX x86 x64|[06/18/2017]|611.59 MB

All credits goes to the respective people

DESCRIPTION

Spoiler:

The DSP audio package, consisting of:

Flux - Full Pack 3.5.29, IRCAM Tools 3.5.29, Level Magic 3.5.29, Pure Analyzer 1.10.4

Of Full Pack 2.2 Flux

  • a package of plugins for Mixing and mastering, comprising:

Alchemist 3.5.29

Flux 3.5.29 Epure

Flux Syrah 3.5.29

Flux Elixir 3.5.29

Flux the Pure Compressor 3.5.29

Flux the Pure DCompressor 3.5.29

Flux the Pure Expander 3.5 . 29

Flux Pure DExpander 3.5.29

Flux Pure Limiter 3.5.29

Ircam Tools 1.1

is a package of spatial and creative processing plug-ins consisting of:

Ircam Spat 3.5.29

Ircam Verb 3.5.29

Ircam Verb 3.5.29

Ircam HEAR 3.5.29

Ircam Trax Transformer 3.5.29

Ircam Trax Cross Synthesis 3.5.29

Ircam Trax Source Filter 3.5.29

Flux Junger Audio Level Magic 3.5.29

  • Real Time & Offline Loudness Processor, including the following functionality:

Input Metering | Loudness Metering | Output Metering | Main Input Gain | Leveler | Transient Processor | Limiter | Expert Mode | Low Level Behavior

Flux Pure Analyzer Essential V1.8.6 + SampleGrabber V3 is a network-driven modular RTA-system, including the following functionality:

Basic metering | Vector Scope | Wave Scope | Magnitude Spectrum | Spectrogram | Spatial Spectrogram (Flux Nebula)

Pure Analyzer 1.10.4 - the analyzer.

.. ##############################

This release is intended for evaluation testing.

Support the manufacturer if you like the software

and you intend to use this software in commercial production,

in accordance with the manufacturer's license agreement.

.. ##############################

The "installation" steps are indicated in curly brackets.

Explanations (read only if necessary) are highlighted in spoilers (or triple square brackets in the txt file attached to the distribution).

{HOW TO "INSTALL" THIS PACKAGE WITH USING .CMD FILES SymLink Installer?}

Despite the following long text, the point is simple:

a) remove some folders left from the old versions of the installed program (if any);

b) run the symlink creation file - SymLink Installer.cmd;

c) specify in DAW the path of scanning VST2 plug-ins (C: \ Program Files (x86) \ VstPlugins), start DAW, scan for new plugins and use;

d) register (if required).

Details - below. {0} {Preinstall necessary system software} Install Microsoft Visual C ++ packages Redistributable,

(if not installed or partially installed)

[addon] Microsoft Visual C ++ 2005-2008-2010-2012-2013-2015 Redistributable Package x86 & x64

forum.oszone.net/thread-145766.html {1} { Unpacking the package correctly} Open the .exe package file using the 7zip archiver shell, and extract the contents to any disk for permanent storage, so that you do not delete it *, for example, in the folder: d: \ Flux 3.5.25 \ - not deep by nesting folders and without Cyrillic. * To ensure the operation of .CMD files SymLink Installer, MOVE, DELETE, RENAME ANYTHING IN THE CONTENT OF THE DISCUSSION IS NOT AVAILABLE.

{2}

{Pre-clearance of possible "remains" of earlier versions of the package}

{2.1} ATTENTION! Save the operating hours (presets, etc.) of the data to be deleted.

{2.2} Uninstall (or delete if there is no uninstaller) previous versions of the one being installed.

{2.3} Check the absence of folders in the places where the symlinks will be created (IF FOLDERS SHOULD, THEN THE SIMILINKS WILL NOT BE CREATED),

and delete the remaining (if left) after uninstalling the folder according to the {PACKAGE OF FINAL PACKAGE SETTINGS} list . {FOLDERS OF FINAL PLACEMENT OF THE PACKAGE CONTENT}

{3} {Actually "installation"}

For instant installation based on symlinks,

run the command file * SymLink Installer.cmd

and, if necessary, change ** the paths to VST2 in .CMD files as administrator (through the context menu) .

{4} {Final stage}

Installation is complete. Next, you need to open the DAW,

specify in the DAW settings an additional path for scanning the VST plug-ins: C: \ Program Files (x86) \ VstPlugins

and perform an update plug-in scan.

For more information, see above: {HOW TO CHANGE THE WAYS TO VST2 IN .CMD FILES SymLink Installer?}

相关推荐